Need Ductwork Installation in Clearwater?

Installing a new duct run in Clearwater typically runs $279 to $950 per run depending on length, attic access, and whether R-6 or R-8 insulation is required under Florida Energy Code. A full ductwork system replacement runs $1,800 to $8,500 for most Clearwater homes. FREE estimates on every job. We give you a flat-rate price before any work begins so you know the total before we touch anything.

Common signs in Clearwater homes include uneven temperatures between rooms, higher electric bills without a usage change, visible kinked or disconnected flex duct in the attic, dusty air despite regular filter changes, and musty smells from the vents. We carry a duct blaster on every truck and can test your system’s leakage rate free while we are on site for any service call.

For attic runs in Clearwater, R-6 or R-8 flex duct with a metalized outer jacket handles heat stress better than single-layer flex. For main trunk lines and plenums, 26-gauge galvanized rigid sheet metal is the most durable option. All connections get sealed with Hardcast mastic compound rather than duct tape, which fails in Tampa Bay attic heat within a few years.

Adding a single new duct run in Clearwater takes 2 to 4 hours for most jobs. A full ductwork system replacement for a 1,500 to 2,000 square foot home takes 1 to 2 days depending on attic access and system configuration. We handle the permit application and county inspection, and both are included in every ductwork quote.

Yes. Any new duct installation or full system replacement in Clearwater requires a permit under Florida Building Code Section 1006 and local county mechanical codes. We pull the permit and schedule the inspection on your behalf. The permit is included in your quote with no separate markup or add-on fee.

Yes. Adding supply and return air to a converted garage, bonus room, enclosed porch, or Florida room in Clearwater is one of our most common ductwork calls. We use Manual D airflow calculations to size the new run correctly so the new room gets adequate airflow without starving other rooms in the house.

Florida Energy Code requires a duct leakage test on any new or replaced duct system in Clearwater. The test uses a duct blaster to measure how much conditioned air escapes before reaching the rooms it serves. We perform the test as part of every ductwork installation and submit the results to the county for permit close-out. We can also test existing systems in about 30 minutes.

Flex duct in a Tampa Bay attic typically lasts 20 to 25 years if it stays intact. Rigid galvanized metal can last 30 years or more. The weakest point is always the connection seals. Duct tape dries out in Florida attic heat in as few as 3 to 5 years. We use Hardcast mastic on every connection, which outlasts the duct itself.

Yes, in most cases. Uneven temperatures are commonly caused by undersized duct runs, imbalanced airflow, or collapsed flex sections that restrict delivery. We perform a Manual D calculation before any ductwork project in Clearwater to make sure each room receives the correct airflow. Properly designed ductwork is the most reliable fix for comfort problems.

We install Johns Manville or Owens Corning R-6 and R-8 flex duct, 26-gauge galvanized sheet metal for trunk lines and plenums, and Hardcast 1402 or MasterSeal mastic for all connections. We do not use duct tape on any connection. All materials meet Florida Energy Code and ACCA Manual D requirements.

A: Yes. Mold spores circulating through HVAC systems are a recognized indoor air quality concern. The EPA and CDC both note that mold exposure can trigger respiratory symptoms, worsen asthma, and cause allergic reactions. In Clearwater, where AC runs most of the year, contaminated ducts cycle air through every room continuously.

A: Surface-level cleaning can remove dust and loose debris, but mold embedded in the fiberglass inner liner of flex duct cannot be fully removed by cleaning. If the musty smell returns within weeks of cleaning, the liner is colonized. Replacement of affected runs is the lasting solution in that case.

A: Clearwater ductwork mold is almost always caused by high attic humidity entering through leaky joints, condensation forming inside ducts during system off-cycles, or moisture entering through disconnected sections. Poor insulation accelerates the cycle. Sealing joints, upgrading to R-8 insulation, and replacing old flex breaks the pattern.

A: The most reliable signs are a persistent musty or earthy smell from registers, visible black or green deposits at duct boots, and worsening allergy or respiratory symptoms indoors. We use a camera to inspect runs during the free visit and document exactly what we find.

A: Ductwork replacement in Clearwater starts at $279 for a single-run repair. Partial system replacement covering 3 to 5 major runs runs $2,500 to $5,500. Full system replacement in a typical 1,600 to 2,400 square foot home runs $4,500 to $12,000 depending on attic access and run count. Estimates are free and written.